> Terms of Use     

HOME PRODUCTS TRACEABILITY Friendly LINK OVERSEAS AGENCY

HOME > PRODUCT Top > Laser Micrometer > Display Unit

Laser Micrometer Display Unit -- Specifications


[Back to LaserMicrometer]
[Go to Scanning Unit Spec.]
[Back]


400 Scan type

LDM-110 LDM-110EX LDM-1000 LDM-1000EX
Picture Go Go Go Go
CAD file dxf dxf dxf dxf
pdf pdf pdf pdf
No. of Axes For Single Max. 2 Max. 5 Max. 3
Scanning cycle 400 times/sec 400 times/sec 400 times/sec 400 times/sec
No. of
Averaging time
1-2048
(16 steps)
1-2048
(8 steps)
1-2048(22 steps) at LDM-1000LS
1-1024(19 steps) at LDM-1000XY
Measuring mode 16 kinds 8 kinds
(X,Y axis each)
16 kinds + Optional edges measurement
per each axis
Processing
function
NG Average, Difference, Large dia. measurement, etc.
Cable cover(Wall)
thickness
processing
NG NG OK(by LDM-1000XY)
Display device 7 segment LED Graphic LCD 7 segment LED
No. of Display digit 4-5 digits 4-5 digits 3-6 digits 3-6 digits
Processing
contents monitor
NG NG OK OK
Center position
monitor
LED(8pcs) LED(8pcs)
(X,Y axis each)
Graphic bargraph
per each axis
LED(8pcs) per each axis
No. of channel of
Recorder output
1 1 1 channel per board(LDM-1000LS/XY)
Recorder output
performance
Max.+/-10V, Resolution 12bits(=approx.10mV/1bit),
Output impedance 100ohm(approx.),
Deviation/Absolute value switch over available
Recorder output
gain
1μm-1m/V(decade steps) 0.1μm~1m/V(decade steps)
Digital dia.
controller
connection
OK OK NG NG
Center value
setting
5 digits 5 digits 6 digits 6 digits
High/Lo limit
tolerance setting
4 digits 4 digits 6 digits 5 digits
High/Low limit
contact output
1a contact(*2) 1a contact(*2) per board(LDM-1000LS/XY)
Contact rating: AC250V 2A(Resistance load)
Error
contact output
1b contact(Close when power OFF) 1b contact(Close when power OFF)(Combined use by each board)
Contact rating: AC250V 2A(Resistance load)
Laser remote
terminal
OK OK
(X,Y common)
OK(each LDM-1000LS board)
Hold terminal OK OK
(X,Y,P common)
OK(each LDM-1000LS/XY board)
Edge monitoring
function
OK OK OK OK
Self-diagnosis
mode
OK OK OK OK
Multi-point
calibration
function
OK NG NG NG
Trigger function
(Max. meas.,
Deviation meas.,
etc.)
NG NG OK OK
Offset
function
NG NG OK OK
Zero set
function
OK NG OK OK
mm/inch
changeover
function
NG NG OK OK
Programing
function
NG NG OK(30 kinds) OK(9 kinds)
Graph display NG NG OK NG
Serial port OK OK OK OK
BCD output Option OK(by LDM-1000BCD)
RS-485 Function Option NG
Cable length Standard 5 meters, Max. 30 meters (Extensible to 120m.max. as option)
Power supply AC100-240V Free power supply 50/60Hz
Power
consumption
less than 11VA less than 14VA less than 15VA(only display unit)
less than 8VA(each board)
Ambient
condition
Temperature:0-45 degree centigrade, Humidity:35~85%RH(no condensation)
Outside
dimension
144(W) * 72(H) * 191(D)[mm] 216(W) * 144(H) * 225(D)[mm]
Weight Approx. 1.5kg Approx. 1.6kg Approx. 4kg (only display unit)
Approx. 280g (each board)


2000/400 Scan type

LDM-210 LDM-210C LDM-210EXC
Picture Go Go Go
CAD file dxf dxf dxf
pdf pdf pdf
No. of Axes For Single Max. 2
Scanning cycle 2000 times/sec or 400 times/sec
No. of
Averaging time
1-2048
(12 steps)
Measuring mode Optional edges measurement
per each axis
Processing
function
NG Average, Difference, Large dia. measurement, etc.
Cable cover(Wall)
thickness
processing
NG
Display device 7 segment LED
No. of Display digit 4-5 digits
Processing
contents monitor
NG
Center position
monitor
LED(8pcs) LED(15pcs) LED(8pcs)
(X,Y axis each)
No. of channel of
Recorder output
1
Recorder output
performance
Max.+/-10V, Resolution 12bits(=approx.10mV/1bit),
Output impedance 100ohm(approx.),
Deviation/Absolute value switch over available
Recorder output
gain
1μm-1m/V(decade steps)
Digital dia.
controller
connection
OK NG
(Built-in Dia.Controller)
Center value
setting
5 digits
High/Lo limit
tolerance setting
5 digits
High/Low limit
contact output
1a contact(*2)
Contact rating: AC250V 2A(Resistance load)
Error
contact output
1b contact(Close when power OFF)
Contact rating: AC250V 2A(Resistance load)
Laser remote
terminal
OK OK(X,Y common)
Hold terminal OK OK(X,Y common)
Edge monitoring
function
OK
Self-diagnosis
mode
OK
Multi-point
calibration
function
OK
Trigger function
(Max. meas.,
Deviation meas.,
etc.)
NG
Offset
function
OK(Ver2.15 or more) NG
Zero set
function
OK NG
mm/inch
changeover
function
NG
Programing
function
NG
Graph display NG
Serial port OK
BCD output Option
RS-485 Function Option
Cable length Standard 5 meters, Max. 30 meters (Extensible to 120m.max. as option)
Power supply AC100-240V Free power supply 50/60Hz
Power
consumption
less than 15VA less than 20VA
Ambient
condition
Temperature:0-45 degree centigrade, Humidity:35~85%RH(no condensation)
Outside
dimension
144(W) * 72(H) * 191(D)[mm] 144(W) * 72(H) * 241(D)[mm]
Weight Approx. 1.5kg Approx. 1.8kg


  • Signal Extender (LDM-201,-202), to be used in case distance between a Scanning Unit and a Display Unit exceeds 30 meters.
                                   For Example => Go
  • Signal distributor (LDM-205,-206), which divides output signals from Scanning Unit.
                                   For Example => Go
  • LDM-210/LDM-210C/LDM-210EXC uses the detection part of the exclusive use because the scan time is different from the conventional model.
  • LDM-B2 BCD distributor  ==> Go         CAD file => dxf format
                                           pdf format

[Go to Top this page]

[Back to LaserMicrometer]
[Go to Scanning Unit Spec.]
[Back]