Product information

Laser Micrometer ・ Scanning Unit specification list

400 scan type

※Please swipe right.

Common specification
Measurement method Non-contact laser scanning method
Light source Semiconductor laser (up to 1 mW), red (670 nm), Class 2 continuous wave
Protective structure Dustproof structure (IP-64)
Operating environment Temperature 0 to 45 ° C Humidity 35 to 85% RH (without condensation)

※Please swipe right.

Individual specification
Type Model No. Measurement range (mm) [*1] Measurement accuracy[*2] Resolution Weight Exterior photo CAD file
1 axis measurement Standard type LDM-301H 0.02 to 1 ±1μm ±0.1μm 1kg Photo dxf pdf
LDM-302H 0.05 to 5 ±1μm ±0.1μm 1kg Photo dxf pdf
LDM-303H 0.3 to 30 ±2μm ±0.1μm 1kg Photo dxf pdf
LDM-304H 0.5 to 90 ±5μm ±1μm 2.9kg Photo dxf pdf
LDM-305H 1 to 180 ±10μm ±1μm 15kg Photo dxf pdf
LDM-306H 2 to 300[*2] ±30μm ±1μm 34kg Photo dxf pdf
Separate type LDM-302H-SP 0.05 to 5 ±1μm ±0.1μm 1kg Photo dxf pdf
LDM-303H-SP 0.3 to 30 ±2μm ±0.1μm 0.9kg Photo dxf pdf
LDM-304H-SP 0.5 to 90 ±5μm ±1μm 2.3kg Photo dxf pdf
LDM-305H-SP 1 to 180 ±10μm ±1μm 11kg Photo dxf pdf
LDM-306H-SP 2 to 300[*2] ±30μm ±1μm 28kg Photo dxf pdf
Orthogonal two-axis measurement LDM-302H-XY 0.05 to 5 ±1μm ±0.1μm 2kg Photo dxf pdf
LDM-303H-XY 0.3 to 30 ±2μm ±0.1μm 2kg Photo dxf pdf
LDM-304H-XY 0.5 to 90 ±5μm ±1μm 14kg Photo dxf pdf
LDM-305H-XY 1 to 180 ±10μm ±1μm 50kg Photo dxf pdf
LDM-306H-XY 2 - 300 ±30μm ±1μm 70kg Photo dxf pdf
Oscillating type all-round measurement[*3] LDM-303H-SP
LDM-703A
0.3 to 30 ±2μm ±0.1μm 9kg[*4] Photo dxf pdf
LDM-304H
LDM-704A
0.5 to 90 ±5μm ±1μm 27kg[*4] Photo dxf pdf
LDM-305H
LDM-705
1 to 180 ±10μm ±1μm 60kg[*4] Photo dxf pdf

[*1]There is also a large diameter measuring system that can measure a larger diameter object.
[*2]Measurement accuracy, when you set the average number of times in a specific area to 256 times or more.
[*3]LDM-703A, 704A, 705 are the models of the swinging mechanism unit alone.
[*4]These weights are the weight of swinging mechanism unit alone.

2000 scan type

※Please swipe right.

Common specification
Measurement method Non-contact laser scanning method (2000 times / second sample)
Light source Semiconductor laser (up to 1 mW), red (670 nm), Class 2 continuous wave
Protective structure Dustproof structure (IP-64)
Operating envirornment Temperature 0 to 45 ° C Humidity 35 to 85% RH (without condensation)

※Please swipe right.

Individual specification
Type Model No. Measurement range (mm) Measurement accuracy[*1] resolution Weight Exterior photo CAD file
1 axis measurement Standard type LDM-301HS 0.03 ~ 1 ±1μm ±0.1μm 1kg Photo dxf pdf
LDM-302HS 0.07 to 5 ±1μm ±0.1μm 1kg Photo dxf pdf
LDM-303HS 0.3 to 30 ±2μm ±0.1μm 1kg Photo dxf pdf
LDM-304HS 0.5 to 90 ±5μm ±1μm 2.9kg Photo dxf pdf
Separate type LDM-303
HS-SP
0.3 to 30 ±2μm ±0.1μm 0.9kg Photo dxf pdf
LDM-304
HS-SP
0.5 to 90 ±5μm ±1μm 2.3kg Photo dxf pdf

[*1]Measurement accuracy, when you set the average number of times in a specific area to 256 times or more.

For other specifications, it will be the contents of the following.
For details, please contact our sales department.

Separation distance of Separated type
LDM-302H-SP --- 20mm Max
LDM-303H-SP --- 400mm Max
LDM-304H-SP --- 1000mm Max
LDM-305H-SP --- 3500mm Max
LDM-306H-SP --- 5000mm Max

High temperature object measurement --- Option up to 2000 ° C possible
Transparent object measurement --- Equipped as standard (Set by Display Unit)
Transparent film width measurement --- possible by option

Laser Micrometer Calibration gauge and Calibration gauge Fixture

※Please swipe right.

Object model Calibration gauge Fixture Calibration gauge diameter (mm)
Lo Hi
LDM-301H Standard mounting Φ0.03 Φ1.0
LDM-302H Standard mounting Φ0.05 Φ5.0
LDM-302H-SP Optional Φ0.05 Φ5.0
LDM-302H-XY L-022  [Photo] Φ0.05 Φ2.0 (Φ5.0)
LDM-303H L-030  [Photo] Φ0.3 Φ10.0
LDM-303H-SP Optional Φ0.3 Φ10.0
LDM-303H-XY L-032B  [Photo] Φ0.3 Φ10.0
LDM-304H L-40  [Photo] Φ2.0 Φ40.0
LDM-304H-SP Optional Φ2.0 Φ40.0
LDM-304H-XY L-042B  [Photo] Φ2.0 Φ40.0
LDM-305H Optional Φ20.0 Φ100.0
LDM-305H-SP Optional Φ20.0 Φ100.0
LDM-305H-XY Optional Φ20.0 Φ100.0
LDM-306H Optional Φ20.0 Φ180.0
LDM-306H-SP Optional Φ20.0 Φ180.0
LDM-306H-XY Optional Φ20.0 Φ180.0

* Calibration gauge diameter can be changed according to customer's request.
* The gauge diameter stated in the calibration gauge diameter is the diameter used in standard products. Even if there is no diameter in this table, calibration may be possible if it is within the measurement range.
* Even not listed gauge diameters is also purchasable.
* Please contact our sales department for the detector with the description of the option on the calibration gauge table.

About actual calibration

Example of calibration method with Laser Micrometer (LDM-110 / LDM-210)

It is not necessary to calibrate the Laser Micrometer it is already calibrated at the time of shipment.
When calibration is necessary, 2 point calibration is performed with large diameter and small diameter. So prepare 2 gauge pins with different reference outside diameter.

For example, the procedure when using a gauge pin of Φ 40 mm as a large diameter and Φ 5 mm as a small diameter is shown.
Suppose the decimal point display of the main display is set to the second from the left. (88.888 display)

  • Set REF PRESET to "40.000".
  • Set the gauge pin of Φ 40 mm as centered as possible in the measurement area of the Scanning Unit.
  • Push the HI switch of the CAL with a thing like a pin. (Please continue pushing for a while)
  • Release the CAL switch when the main display is displayed as "88888" and then "40000" is displayed. (This completes the calibration of Φ 40 mm)
  • Set REF PRESET to "05.000".
  • Set the gauge pin of Φ 5 mm as centered as possible in the measurement area of the Scanning Unit.
  • Push the LO switch of the CAL with a thing like a pin. (Please keep pushing for a while)
  • Release the CAL switch when it is displayed as "88888" and then "05000" on the main display. (This completes the calibration of Φ 5 mm)

This completes the calibration between Φ 5 and 40 mm.

LDM-301H

LDM-302H

LDM-303H

Dust cover

LDM-304H

LDM-305H

LDM-306H

LDM-302HS

Outside Dimension : [W * H * D] LDM-210:144×72×191(mm)/ LDM-302HS:165×115×50(mm)
Left: LDM-210 / Right: LDM-302HS

LDM-302H-SP

LDM-303HS

Outside Dimension : [W * H * D] LDM-210:144×72×191(mm)/ LDM-303HS:289×89×45(mm)
Left: LDM-210 / Right: LDM-303 HS

LDM-304HS

Outside Dimension : [W * H * D] LDM-210:144×72×191(mm)/ LDM-304HS:450×154×60(mm)
Left: LDM-210 / Right: LDM-304 HS

LDM-303HS-SP

Outside Dimension : [W * H * D] LDM-210:144×72×191(mm)/ LDM-303HS-SP:Emitter 114×90×45(mm)& Receiver 80×90×45(mm)
Left: LDM-210 / Right: LDM-303 HS-SP

LDM-303H-SP

Outside Dimension:[W * H * D] Emitter 114×90×45(mm)/ Receiver 80×90×45(mm)

LDM-304H-SP

LDM-305H-SP

LDM-306H-SP

LDM-302H-XY

LDM-303H-XY

LDM-304H-XY

LDM-305H-XY

LDM-306H-XY

LDM-703A

LDM-704A

LDM-705

L-022(For LDM-302H-XY)
  • L-022(For LDM-302H-XY)

  • Example of use

L-030(For LDM-303H)
  • L-030(For LDM-303H)

  • Example of use

L-032B(For LDM-303H-XY)
  • L-032B(For LDM-303H-XY)

  • Example of use

L-040(For LDM-304H)
  • L-040(For LDM-304H)

  • Example of use

L-042B(For LDM-304H-XY)
  • L-042B(For LDM-304H)

  • Example of use

Segnal Distributor / Signal Extender of Laser Micrometer

LDM-B2
  • External dimension 200×150×80(mm)

Air purge unit for Laser Micrometer

** Air purge units for LDM-303H, LDM-304H, LDM-303H-XY are available.**

This unit is a dustproof unit for preventing dirt from adhering to the glass filter surface of the Scanning Unit at a line with poor measurement conditions. When using, please put cleaned air from the compressor. For models not listed, please?contact our sales department.

Laser Micrometer ・ Display part specification list

400 scan type

※Please swipe right.

LDM-110
(Discontinued product)
LDM-110EX
(Discontinued product)
LDM-1000EX LDM-1000
Exterior photo photo photo photo photo
CAD File dxf dxf dxf dxf
pdf pdf pdf pdf
Number of measurement axes 1 Axis Only Up to 2 axes Up to 3 axes Up to 5 axes
Number of samples 400 times / sec 400 times / sec 400 times / sec 400 times / sec
Average times 1 to 2048 times
(16 steps)
1 to 2048 times
(8 steps)
For LDM - 1000 LS, 1 to 2048 times (22 steps)
For LDM-1000XY 1 to 1024 times (19 steps)
Measurement mode 16 kinds 8 types of each axis 16 types of each axis + measurement between arbitrary edges
Wall thickness calculation function - × Yes (possible with LDM-1000 XY)
View Measured value display Device 7 segment LED 7 segment LED Graphic LCD
Number of display digits 5 digit 6 digits 6 digits
Computation contents - ["1", "average
2 "," difference
3 "," ratio
4 "," large caliber measurement "]
["1", "average: (X + Y) / 2
2 "," Difference: X - Y
3 "," ratio: X / Y
4 "," (XY) / 2
5 "," X + Y
6 "," large caliber measurement "]
Computation content display -
Work position monitor Displayed in 8 LEDs Indicated by 8 axis LEDs Each axis graphic bar graph
Analog output Number of output channels 1 LDM-1000 LS and LDM-1000 XY
One channel for each board
Output performance Maximum ± 10 V, resolution 12 bits (= about 10 mV resolution),
Output impedance approx. 100 Ω, deviation / absolute value changeable
Output gain 1 μm to 1 m / V (10 times step) 0.1 μm to 1 m / V (10 times step)
Digital outer diameter control connection × ×
Center value setting 5 digit 5 digit 6 digits 6 digits
Upper / Lower limit tolerance setting 4 digits 4 digits 5 digit 6 digits
Contact output Upper and lower limit contact outputs 1 a contact × 2 LDM-1000 LS and LDM-1000 XY
1 "a" contact × 2 each board
Error contact output 1 b contact × 1 (Closed when power is OFF) 1 "b" contact (closed at power off, 1 at full slot)
Contact rating AC 250V 2A (resistance load)
Laser remote terminal ○ (Common to X / Y) ○ (1 for each LDM-1000LS board)
Hold terminal
(Common to X / Y / P)
○ (1 for each LDM-1000LS and LDM-1000XY board)
Edge monitoring function
Self-diagnosis function
Multi-point calibration function No
(Since ver.3.0)
×
Trigger function
(Max / shake etc.)
× ×
Offset function × ×
Zero set function No
Unit switching function × ×
Program function × × ○ (9 ways) ○ (30 ways)
Graph display × × ×
RS-232C communication
BCD output Optional Supported by LDM-1000BCD board
RS-485 communication Optional -
Pair Detection Code Cord Length Standard 5 m, maximum 30 m (maximum 120 m if cable extension box is used)
Power supply AC 100 to 240 V free power supply 50/60 Hz
Power consumption Below 11VA Below 14VA It is less than 15VA by itself
(Less than 8 VA per one LDM-1000LS and LDM-1000XY board)
Operating envirornment Temperature: 0 to 45 ° C, humidity: 35 to 85% RH (without condensation)
Outline dimension
(W × H × D [mm])
144 × 72 × 191 [mm] 216 × 144 × 241 [mm]
Weight Approx 1.5 kg Approx 1.6 kg Approx 4 kg
(About 280 g per board for LDM-1000LS and LDM-1000XY board)
400/2000 scan type (Note 1)

○: Yes, ×: none, -: not applicable

※Please swipe right.

LDM-210 LDM-210EX LDM-130 LDM-130EX
Exterior photo photo photo photo photo
CAD file dxf dxf dxf dxf
pdf pdf pdf pdf
Number of measurement axes 1 Axis Only 2 Axis Maximum 1 Axis Only 2 Axis Maximum
Number of samples 400/2000 scan type
Average times 1 to 2048 times (12 steps)
Measurement mode Arbitrary edge measurement
Wall thickness calculation function - - - -
View Measured value display Device 7 segment LED
Number of display digits 5 digit maximum
Computation contents EX mode by using 2 devices ①Average(X/Y)/2
②Difference
③Ratio X/Y
④Mesurement of large diamiter
- ["1", "average: (X + Y) / 2
2 "," Difference: X - Y
3 "," ratio: X / Y
4 "," (XY) / 2
5 "," X + Y
6 "," large caliber measurement "]
Computation content display ○(EX mode) -
Work position monitor Displayed in 8 LEDs
Analog output Number of output channels 1 channel
Output performance Maximum ± 10 V, resolution 12 bits (= about 10 mV resolution), output impedance about 100 Ω, deviation / absolute value switching
Output gain 1 μm to 1 m / V (10 times step)
Digital outer diameter control connection
Center value setting 5 digit 5 digit segment LED display
Upper / Lower limit tolerance setting 5 digit 4 digit segment LED display
Contact output - - Displays the maximum value or the minimum value of averaged value of measured data
USB connector - - Setting Data load/save via USB Memory
Contact output Upper and lower limit contact outputs 1 "a" contact × 2
Error contact output 1 "b" contact × 1 (Closed when power is OFF)
Contact rating AC 250V 2A (resistance load)
Laser remote terminal ○(X/Y common) ○(X/Y common)
Hold terminal ○(X/Y common) ○(X/Y common)
Edge monitoring function
Self-diagnosis function
Multi-point calibration function
Trigger function
(Max / shake etc.)
× ×
Offset function ○ (Since ver 2.15) × × ×
Zero set function × × ×
Unit switching function × × × ×
Program function × × × ×
Graph display × × × ×
RS-232C communication ○(Standerd equipment)
RS-485 communication Optional Standerd equipment [Modbus RTU 2 line type]
CC-LINK - - Optional
Ethernet-IP - - Optional
BCD output Optional 6 digit Optional
Pair Detection Code Cord Length Standard 5 m, maximum 30 m
(Maximum 120 m if cable extension box is used)
Power supply AC 100 to 240 V free power supply 50/60 Hz
Power consumption 15VA or less 20VA or less
Operating envirornment Temperature: 0 to 45 ° C, humidity: 35 to 85% RH (without condensation)
Outline dimension
(W × H × D [mm])
144 × 72 × 191 [mm]
Weight Approx 1.5 kg Approx 1.6 kg Approx 1.8 kg

When the cable between the scanning unit and the display unit exceeds 30 m , please use Signal Extender LDM-201 (for 1 axis) and LDM-202 (for 2 axis) .
(It is possible to extend the cable to 120 m by using the Signal Extender)
An example of using the Signal Extender>

Please use the Signal Distributor LDM-205 (1 → 2 distribution) and LDM-206 (1 → 3 distribution).when distributing the Scanning Unit.
An example of how to use the Signal Distributor>

To distribute the BCD signal, please use the BCD Distributor LDM-B2.

Photo is here
CAD drawing is here
PDF drawing is here

Note 1)
Use a suitable Scaning Unit for 2000 times/second when the sampling times of the Display unit is set to 2000 times/second.
For detailsplease contact our sales department.

Laser Micrometer・Display
  • Outside Dimension : [W * H * D] 144×72×191(mm)
    LDM-130

  • Outside Dimension : [W * H * D] 144×72×191(mm)
    LDM-130EX

  • Outside Dimension : [W * H * D] 144×72×191(mm)
    LDM-110

  • Outside Dimension : [W * H * D] 144×72×191(mm)
    LDM-110EX

  • Outside Dimension : [W * H * D] 216×144×241(mm)
    LDM-1000EX

  • Outside Dimension : [W * H * D] 216×144×241(mm)
    LDM-1000

  • Outside Dimension : [W * H * D] 144×72×191(mm)
    LDM-210

Laser Micrometer / Deflection Micrometer

The product introduced here is an example.
Since there are many application examples yet, please contact our sales department for details.

※Please swipe right.

Mearsuring target item Cylindrical articles such as rubber rolls, metal rolls, pipes,
CAD file 304H specification dxf pdf
OD Φ 1 to Φ 80 (outer diameter measurement range)
測定分解能 1μm
Repeatability Outer diameter: ± 2 μm
Runout width: ± 2 μm
Outer diameter accuracy ± 5 μm (when Φ 40 mm or less)
Runout accuracy Within 7 μm
Measurement object length range 80 mm to 320 mm (Distance between work bearings)
Work receiving Bearing receiving
Work rotation speed (At the time of Φ 10 mm work) about 3 turns The rotation control method is a speed control motor driving method
Work weight 5 kg or less
Outer diameter ・ runout width Measuring base weight
19kg
System weight 25kg
Power supply AC 100 V ± 10% 50/60 Hz 40 VA

※In case of Φ25mm, LDM-303H-SP is applicable

* The actual size of the printer paper is about 57 mm wide.

LDM-WTM specification

※Please swipe right.

Model No. LDM-WTM
(Build-to-order manufacturing)
CAD file Rotary unit dxf pdf
LDM-210 dxf pdf
Operating condition Used PC
The Windows OS to use should operate comfortably (Operation is not guaranteed for Windows emulator) Be able to use CD-ROM. Screen display size 1024 x 768 or more. PC card Standard TYPE II standard PC card can be installed. Serial port or USB port is installed in the main unit and it is operating.
Used OS Micrisoft Windows XP, Vista, 7 (32 bit version: MS company out of license OS or 64 bit version are not guaranteed operation)
Serial communication condition 19200 bps recommended
communication speed Data bit 8 bits, stop bit 1 bit, no parity
Functions Measured value display Wall thickness measurement value, outside diameter measurement value
Peak value display Display maximum value and minimum value during measurement (hold numerical value)
Measurement status display Alarm indication, OK indication, Error display and each set value when the upper and lower limit set values ??are exceeded.
Measurement data record Measurement place, average value, maximum value, minimum value
Measurement data recording interval Minimum 5 degrees (72 circumference divided, measurement time about 5 seconds)
Graph Display measurement data in real time, print function
Measurement object shape Cylindrical hollow products (transparent objects can also be measured) Inside diameter Φ 5.5 mm or more, outer diameter Φ 50 mm or less Length about 30 mm (Inner diameter Φ 5.5 mm or less, outer diameter Φ 50 mm or more is optional)
Measurement accuracy ± 5 μm According to LDM-304H
Configuration system LDM-210, LDM-304H, rotary unit, personal computer

EM series / Eccentricity monitor

Common specification

※Please swipe right.

Measurement target An electric wire coated with an insulator on a circular conductor
Operating environment Temperature 5 to 40 ° C, humidity 35% to 85% RH (without condensation)
Analog output Eccentricity (X, Y, R, θ axis), OD deviation (X, Y, average), Outer diameter absolute value (X, Y, average)
Alarm output (relay) Outer diameter upper limit, outer diameter lower limit, excess eccentricity amount, error (incorrect position)
File output Measurement data can be stored in CF, USB memory, etc.
RS-232C interface Data bit 8 bits, Stop bit 1bit, Non-parity, Communication speed 19200 bps recommended.
RS-485 interface Optional
Display unit EM-PC 2 Panel computer (316 x 256 x 49.2 [mm] 3.5 kg)
Installation resistance value Third type installed resistance value (less than 100 Ω)
AC power supply AC90 to 240V 50/60Hz less than 50VA
Individual specification

※Please swipe right.

Model No. EM-302B
(Build-to-order manufacturing)
EM-303B
(Build-to-order manufacturing)
EM-304A
(Build-to-order manufacturing)
EM-304B
(Build-to-order manufacturing)
Detection unit EM-302B EM-303B EM-304A EM-304B
Controller unit EM-200B
(Build-to-order manufacturing)
Display unit EM-PC2
(Build-to-order manufacturing)
Power Amplifier EM-1000
(Build-to-order manufacturing)
Excitation unit EM-800
(Build-to-order manufacturing)
Equipment on the main body EM-125
(Build-to-order manufacturing)
dxf format
CAD file
Measurement unit EM-302B EM-303B EM-304A EM-304B
Control unit EM-200
Excitation unit EM-800 --- EM-125
PDF format
CAD file
Measurement unit EM-302B EM-303B EM-304A EM-304B
Control unit EM-200
Excitation unit EM-800 --- EM-125
Condition of measured electric wire Finish OD
(mm)
0.3 to 5[*1] 0.3 to 15 0.8 to 30 0.8 to 45
Outer diameter of core wire
(mm)
0.1 to 3[*2] 0.1 to 10 0.5 to 20 0.5 to 35
Outer diameter accuracy
[*3]
±0.002mm ±0.002mm ±0.005mm ±0.005mm
Eccentricity accuracy ±0.01mm[*4] ±0.015mm[*4] ±0.02mm[*5] ±0.03mm[*5]
General outline Size Detection unit 180 x 175 x 60.4 [mm] 225 x 260 x 64.4 [mm] 526 x 530 x 348 [mm] 606 x 606 x 353 [mm]
Control unit 202 x 82 x 100 [mm]
Display unit 316 x 256 x 49.2 [mm]
Power Amplifier 280 x 137 x 281 [mm]
Excitation unit 119.3 x 124.6 x 144 [mm] --- 290 x 275 x 203 [mm]
weight Detection unit 2kg 6kg 38kg 57kg
Control unit 1.9kg
Display unit 3.6kg
Power Amplifier 5kg
Excitation unit 2.2kg --- 15kg

[*1] Up to 5 mm can be measured depending on usage.
[*2] Up to 3 mm can be measured depending on usage.
[*3] This condition applies to X axis and Y axis respectively.
[*4] Measurement accuracy is guaranteed when the center position of the electric wire satisfies the condition within ± 2 mm of the center position.
[*5] Measurement accuracy is guaranteed when the center position of the electric wire satisfies the condition within ± 5 mm of the center position.

Control unit
  • Outside Dimension 121×117×280[mm] EM-200/EM-204

CPM capacitance monitor

※Please swipe right.

Display unit Type CPM-401 B
CAD file dxf pdf
Measurement range 0 to 400 pF / m (It is possible to expand the measurement range by designation)
Measurement accuracy ± 0.2% of reading value, or ± 0.2 pF / m whichever is larger
Resolution 0.1 pF / m
Sampling time 500 times / sec
Display Capacitance 4 digit green 7 segment LED
Capacity deviation 4 digit red 7 segment LED LED bar graph (FS is selected from ± 10 pF / m or ± 100 pF / m)
Target value setting 4 digit digital switch
High / low limit setting 3 digit digital switch
Averaging process Moving average (1 to 5000 times, 1/2/5 steps)
Zero adjustment Automatic adjustment by pushing the ZERO switch on the front
Output Analog output Capacitance or deviation output within ± 10 V DC, selectable gain, insulated type
Upper and lower limit contact outputs Upper and lower limit red LED display and 1a contact output (AC 250 V 2A resistive load)
BCD output Optional
External communication RS - 232C interface (standard equipment), RS - 485 interface (option)
Control Method Simple proportional control
Output DC ± 10 V voltage output, insulated type
Line speed 3000 m / min
Power supply AC 100 to 240 V free power supply 50/60 Hz 10 VA
Operating temperature 9.1.12.
Operating humidity 35 to 85% RH (no condensation)
Operating Humidity 144 x 72 x 191 [mm]
Weight Approx 1.7 kg
Repeater unit Model CPM-101B
CAD file dxf pdf
Construction Aluminum die casting, dustproof and waterproof structure
Operating temperature 9.1.12.
External Dimensions 80 x 125 x 57 [mm]
Weight Approx 1.7 kg
Detection unit CP-05B CP-05B CP-09B CP-15B
Recommended cable outer diameter Φ5 mm Φ9 mm Φ15 mm
Passing hole diameter Φ8 mm Φ15 mm Φ24 mm
Detection unit Shape: φ28 x 226 mm, 0.5 kg Shape: φ40 × 386 mm, 1 kg Shape: φ60 × 656 mm, 3 kg
Standard water conductivity 1 mS / cm or less (There are differences depending on water temperature and dissolved substances.0.5 mS / cm or less recommended)
CP Series Cable Capacitance Monitor Detector

※Please swipe right.

Model No. CP-05B CP-09B CP-15B
Recommended cable outer diameter Φ5mm Φ9mm Φ15mm
Passing hole diameter Φ8mm Φ15mm Φ24mm
External view CP-05B 外観図 CP-09B 外観図 CP-15 外観図
CAD file dxf dxf dxf
pdf pdf pdf
CPR series calibration capacitor for cable capacitance monitor

※Please swipe right.

Model CPR-05 (for CP-05 (B)) CPR-09 (for CP-09 (B)) CPR-15 (for CP-15)
CAD file dxf pdf dxf pdf dxf pdf
Dielectric / electrode material Pyrex glass / SUS 304
Construction Adhesion of electrode to Pyrex glass center
Reference capacity Notation on each calibration capacitor
Uncertainty Within ± 0.2% of the notation value
Reference temperature 23 ± 5 ° C
Guaranteed temperature 15 to 35 ° C
Operating temperature 1 to 50 ° C (without freezing)
Capacitor dimmension Outer diameter φ7, total length 285 mm (CPR - 05) / total length 445 mm (CPR - 09) / total length 725 mm (CPR - 15)
Measureing accuracy 0.0005
Measuring frequency 1MHz
Protective on case Material: PVC, Storage temperature: 10 to 40 ° C Outline: φ36 × 360 mm (CPR-05) / φ 48 × 520 mm (CPR-09) / φ 36 × 795 mm (CPR-15)

After purchase, traceability of the calibration capacitor will be received at a fee upon request.
Calibration capacitors for CP-15 and CP-26 can also be prepared.
Calibration capacitors for capacitance monitors from other manufacturers will also respond to consultation.
For details of the measuring method, please contact us.

FB-240 / Optical fiber curl measuring instrument

※Please swipe right.

Model No. FB-240 (detection unit)
CAD file dxf pdf
Adaptive Fiber 124μm cladding diameter glass fiber
Measured curvature range 0 to 0.5 [1 / m]
Light source Semiconductor laser (680 nm visible light)
Width between two beams 20 mm
Distance between fiber and screen About 243 mm
Line sensor CCD linear sensor (5000 bits 7 μm / bit)
Connection between sensor unit and host PC RS-232C(19200bps Non-Parity Data-8bit 1-Stopbit)
Measurement (= waveform display) cycle About 0.32 seconds
External communication function RS-232C (separate port is required for sensor connection)
Power supply for sensor section AC 100 to 240 V 50/60 Hz free power supply (8 VA or less)
Operating temperature 0 to 45 ° C
Humidity used 30 to 85% (without condensation)
Outside dimension of sensor part W × H × D 144 mm × 72 mm × 191 mm
Weight of sensor section Approximately 3 kg

RMT-01 / Running Metal Wire Thermometer

RMT-01

※Please swipe right.

Model No. RMT-01
CAD file dxf pdf
Detection sensor K thermocouple
Measured Temperature Range 10 to 250 °C
Display 7-segment LCD 4 digits
Indication number of times 1 time / s
Power supply Four AA batteries and AC adapter
Power consumption 6 V 0.4 A (dry battery)
5 V 0.5 A (rechargeable battery)
Approximately 4 hours when using batteries and Sanyo Electric Eneloop Battery.
Operating temperature / humidity 0 to 45 °C / 35 to 85% RH (without condensation)
External Dimensions Main body 70 x 157.4 x 34.5 [mm]: Pulley Φ 100 mm
Weight Approximately 0.7 kg (including batteries)
RMR-01 Temperature Calibrator for Running Metal Wire Thermometer

※Please swipe right.

Model No. RMR-01
(Build-to-order manufacturing)
CAD file dxf pdf
Compatible models RMT-01
Heater part material Copper
Heater section thickness 0.5 mm
Setting temperature range 0 to 150 °C
Heater temperature accuracy Set value ± 3 °C (at set temperature 100 °C)
Heater internal temperature variation ± 3 °C
Power supply AC 100V
Power consumption 200 W (when heater is ON)
Specification temperature / humidity 0 to 45 °C / 35 to 85% RH (without condensation)
External Dimensions 800 x 75 x 100 [mm]
Weight Approximately 6 kg

LD-50 / Contact type thickness measuring instrument (OEM)

※Please swipe right.

Model LD-50HL LD-50AH
Measuring method Roller contact type
Measurement range ± 25 mm
Measurement accuracy Within ± 50 um (within ± 20 um depending on conditions)
Resolution 10 um
Display 00.00 mm
Analog output ± 1 V / ± 1 mm (Max.± 10 V)
Alarm output Upper / Lower Limit Alarm Lamp, Upper / Lower Limit Relay Contact Output AC 200 V 1A Resistance Load
Power supply AC 90 - 240 V free power supply, 50/60 Hz 15 VA
Outer dimension (W × H × D [mm]) and weight Head: 70 × 125 × 240 / 2.7 kg
Controller: 158 x 108 x 205 / 2.5 kg

Sales in Japan only

TM / Surface Variation Detector

※Please swipe right.

Fine wire counterpart (Measurement object diameter: Φ 0.02 to 3 mm, 0.02 to 5 mm)
Model No. TM-503W TM-1100XY TM-1003W TM-1104W
Exterior photo Photo Photo Photo Photo
CAD file dxf
Power supply unit (PW-02)
dxf
[*1]
dxf dxf
Power supply unit (PW-01)
dxf
[*1]
dxf
pdf
Power supply unit (PW-02)
pdf
[*1]
pdf pdf
Power supply unit (PW-01)
pdf
[*1]
pdf
Direction of detection 3 directions 2 directions 3 directions 4 directions
Measurement method Double slit infrared LED projection type
Adaptive work outer diameter φ0.02 to 3 mm φ0.02 to 10 mm φ0.02 to 5 mm φ0.02 to 10 mm
Unevenness detection range 0.02 to 1 mm
Unevenness detection accuracy Maximum setting within ± 1%
Slit length 6 mm 18 mm 12 mm 18 mm
Slit width 0.1 mm 0.5 mm
Linear speed [*1] 5 m / min to 2000 m / min 1 m / min to 1500 m / min
Recorder output ± 0.2 V / 0.1 mm ± 1 V / 0.1 mm ± 0.5 V / 0.1 mm ± 1 V / 0.1 mm
Alarm output Uneven red LED lit, Relay contact output (AC 250 V 2A resistive load)
Alarm time [*2] 0.1 seconds 0.5 seconds 0.1 seconds 0.5 seconds
Operating temperature -5 to 50 ° C (without condensation)
Power supply [*3] DC ± 15 V AC 100V
50/60 Hz
DC ± 15 V AC 100V
50/60 Hz
Power consumption 6VA 10VA 6VA 10VA
Outline Dimensions (mm) 150 × 140 × 40 260 × 265 × 60 150 × 140 × 40 350 × 280 × 55
Weight 0.8kg 2.5kg 1kg 5kg

[*1] PW-01 is a power supply dedicated to TM-1003W.PW-02 is a power supply for both TM-503W and TM-1003W.
(The enclosures are the same size for PW-01 and PW-02.)
[*2] Applicable line speed range changes depending on the hight of lump.
[*3] Alarm output can be hold by option
[*4] AC200V power supply specification is also available as an option.

※Please swipe right.

Medium wire counterpart (Measurement object diameter: Φ 0.1 to 35 mm)
Model No. TM-3001W TM-3002W TM-3004WA TM-3008W
(TM-3004WA)
(TM-3004WB)
TM-3016W
(TM-3004WA)
(TM-3004WB)
(TM-3004WC)
(TM-3004WD)
Exterior photo Photo Photo Photo Photo Photo
CAD file dxf dxf dxf dxf dxf
pdf pdf pdf pdf pdf
Direction of detection 1 direction 2 directions 4 directions 8 direction 16 directions
Measurement method Double slit infrared LED projection type
Adaptive work outer diameter φ 0.1 - 35 mm
Unevenness detection range 0.05 to 10 mm
Unevenness detection accuracy Maximum setting within ± 1%
Slit length 48 mm
Slit width 1 mm
Linear speed [*1] 1 m / min to 1500 m / min
Recorder output ± 0.1 V / 0.1 mm (for each axis)
Alarm output Uneven red LED lit, Relay contact output (AC 250 V 2A resistive load)
Alarm time [*2] 0.5 seconds
Operating temperature -5 to 50 ° C (without condensation)
Power supply [*3] AC 100 V 50/60 Hz
Power consumption 5VA 10VA 10VA 20VA 40VA
Outer dimension 260 × 90 × 41 [mm] 260 × 260 × 60 [mm] 370 × 355 × 60 [mm] 370 × 355 × 120 [mm] 370 × 355 × 240 [mm]
Weight 1.5kg 3kg 6kg 12kg 24kg

[*1] Applicable line speed range changes depending on the hight of lump.
[*2] Alarm output can be hold by option
[*3] AC200V power supply specification is also available as an option.

※Please swipe right.

Bold wire counterpart (Measurement object diameter: Φ 0.1 to 60 mm)
Model No. TM-4001 TM-4002 TM-4004A TM-4008
(TM-4004A)
(TM-4004B)
TM-4016
(TM-4004A)
(TM-4004B)
(TM-4004C)
(TM-4004D)
Exterior photo Photo Photo Photo Photo Photo
CAD file dxf dxf dxf dxf dxf
pdf pdf pdf pdf pdf
Direction of detection 1 direction 2 directions 4 directions 8 direction 16 direction
Measurement method Infrared LED projection type Double slit infrared LED projection type
Adaptive work outer diameter φ 0.1 - 60 mm
Unevenness detection range 0.05 to 10 mm 0.15 to 10 mm
Unevenness detection accuracy Maximum setting within ± 1% Maximum setting within ± 2%
Slit length 70mm
Slit width 1.5mm
Linear speed [*1] 1 m / min to 1000 m / min
Recorder output ± 0.1 V / 0.1 mm (for each axis)
Alarm output Alarm red LED on, Relay contact output (AC250V 2A resistive load) LED lighting (concave: yellow / convex: red), relay contact output (AC 250 V 2A resistive load unevenness output separately)
Alarm time [*2] 0.5 seconds
Operating temperature -5 to 50 ° C (without condensation)
Power supply [*3] AC 100 V 50/60 Hz
Power consumption 10VA 20VA 30VA 60VA 120VA
Outer dimension 450 * 120
× 50 [mm]
640 * 560
× 160 [mm]
807 * 674
× 136 [mm]
807 * 674
× 272 [mm]
807 × 680
× 424 [mm]
Weight 3kg 25kg 38kg 76kg 152kg

[*1] Applicable line speed range changes depending on the hight of lump.
[*2] Alarm output can be hold by option
[*3] AC200V power supply specification is also available as an option.

※Please swipe right.

Applicabe to extra thick wire (Measurement object diameter: Φ 1 mm to 80 mm, 1 to 130 mm)
Model No. TM-6004A TM-6008
(TM-6004A)
(TM-6004B)
TM-7003A TM-7009
(TM-7003A)
(TM-7003B)
(TM-7003C)
Exterior photo Photo Photo Photo Photo
CAD file dxf dxf dxf dxf
pdf pdf pdf pdf
Direction of detection 4 directions 8 direction 3 directions 9 direction
Measurement method Single slit white tungsten lamp floodlight type
Adaptive work outer diameter φ 1 to 80 mm φ1 to 130 mm
Unevenness detection range 0.2 to 10 mm
Unevenness detection accuracy Maximum setting value within ± 2%
Slit length 95 mm 135 mm
Slit width 1.5 mm
Linear speed [*1] 0.3 m / min to 500 m / min
Recorder output ± 0.1 V / 0.1 mm (for each axis)
Alarm output LED lighting (concave: yellow / convex: red), relay contact output (AC 250 V 2A resistive load unevenness output separately)
Alarm time [*2] 0.5 seconds
Operating temperature -5 to 50 ° C (without condensation)
Power supply [*3] AC 100 V 50/60 Hz
Power consumption 30VA 60VA 30VA 90VA
概略外寸 720 x 660
× 153 [mm]
720 × 660
× 306 [mm]
990 × 930
× 125 [mm]
990 × 930
× 375 [mm]
Weight 38kg 76kg 60kg 180kg

[*1] Applicable line speed range changes depending on the hight of lump.
[*2] Alarm output can be hold by option
[*3] AC200V power supply specification is also available as an option.

In addition to this, you can also prepare products such as TM-6020 (20 axis) and other multi-axis products.

Gauge Fixture / Calibration gauge unit for Surface Variation Detector
Calibration gauge unit

※Please swipe right.

Gauge outer diameter (mm) Model Accuracy
Φ1.0 TMG-10 ±1μm
Φ0.5 TMG-05 ±1μm

Note) It can be available down to Φ0.1.

Gauge Fixture and corresponding gauge unit table

※Please swipe right.

Target Model Calibration gauge to use Mounting jig type
TM-1000S TMG-05 01
TM-1003 TMG-05 02
TM-1000XY TMG-05 03
TM-1004 TMG-05 04
TM-1100XY TMG-05 05B
TM-1003W TMG-05 06B
TM-1104W/TMS-1104W TMG-05 07B
TM-503W TMG-01 16B
TM-3001W TMG-10 08B
TM-3002W TMG-10 09
TM-3004W TMG-10 10B
TM-3008W TMG-10 10B
TM-3016W TMG-10 10B
TM-4001/4001W TMG-10 ----
TM-4002 TMG-10 12B
TM-4002W TMG-10 17B
TM-4004 TMG-10 13B
TM-4008 TMG-10 13B
TM-4016 TMG-10 13B
TM-6004 TMG-10 14B
TM-6008 TMG-10 14B
TM-6016 TMG-10 14B
TM-7003 TMG-10 15B
TM-7009 TMG-10 15B
Example of calibration method (TM-3004W)

Although our detectors are calibrated at the time of shipment, when it is necessary to perform calibration for checking the sensitivity at the time of inspection etc., please perform calibration according to the following method with the calibration gauge unit. The calibration gauge unit to be used is "TMG - 10, Gauge Fixture 10B".

** Before calibration, please be sure to clean the glass filter of the projecting / receiving part and warm up for 10 minutes.

I will explain with 1 axis as an example.

  • Set the Gauge Fixture according to the axis for calibration (this time, 1 axis). (The figure below)
  • Set the level setting dial to "1.00".
  • Insert the gauge tip quickly into the center of the measuring range. At this time, please insert gauge so as not to be inclined as much as possible.
  • When the gauge tip is inserted while repeating the insertion several times, adjust the gain setting VR of 1 axis the lowest to light up the detection alarm lamp.(herein after lamp)
    * It is not abnormal although the lamp may light up when extracting the tip of the gauge.
    * Set an interval of about 3 seconds after the lamp is turned off when repeating the insertion of the gauge tip.
    * VR for gain setting increases sensitivity when turned clockwise, and decreases when turning it counterclockwise.
  • Change the level setting dial to "1.03".
  • Repeat the insertion of the gauge tip in the same way.Now adjust the VR for 1 axis gain adjustment so that the lamp does not light up when inserting the tip of the gauge.
  • The calibration will be completed after repeating steps (2) - (6) several times to light up at "1.00" and not light up at "1.03".
For Thin Wire
  • Outer dimension[W * H * D] 150×140×40(mm)
    TM-503W

  • Outer dimension[W * H * D] 260×265×60(mm)
    TM-1100XY

  • Outer dimension[W * H * D] 150×140×40(mm)
    TM-1003W

  • Outer dimension[W * H * D] 350×280×55(mm)
    TM-1104W

For Medium Wire
  • Outer dimension[W * H * D] 260×90×41(mm)
    TM-3001W

  • Outer dimension[W * H * D] 260×260×60(mm)
    TM-3002W

  • Outer dimension[W * H * D] 370×335×60(mm)
    TM-3004WA

  • TM-3008W

  • TM-3016W

For Thick Wire
  • Outer dimension[W * H * D] 540×160×100(mm)
    TM-4001

  • Outer dimension[W * H * D] 630×560×160(mm)
    TM-4002

  • Outer dimension[W * H * D] 807×674×136(mm)
    TM-4004

  • TM-4008

  • TM-4016

Applicabe to extra thick wire
  • Outer dimension[W * H * D] 720×660×153(mm)
    TM-6004A

  • TM-6008

  • TM-7003A

  • TM-7009

TML/ surface Variation Detector

※Please swipe right.

Model No. TML-02
Unevenness No.display 3 digits (1 to 999)
Height of unevenness display 4 digits (≦ 1.000)
Display of mesurement 6 digits
Input from detector Encoder input
Power supply output for detector DC 12V Max. 50mA
Alarm output 1 Relay contact output (Max: AC 250 V ・ 10 A)
Alarm output 2 Relay contact output (Max: AC 250 V ・ 10 A)
External contact input Reset input, measurement start input
RS-485 communication standard equipment
Detector cable length 5m (Standard equipment)
Alarm time 0.1 to 1.0 sec. (0.1 sec unit)
Power supply AC 90 to 240 V free power supply 50/60 Hz
Power consumption 10VA (Display unit only)
Weight Approximately 2 kg

※Please swipe right.

Model No. TML - 1003 W
Direction of detection 3 directions
Measurement method Double slit infrared LED light projection type
Adaptive work external diameter Φ 0.02 to 5 mm
Unevenness detection range 0.020 to 1.000 mm
Unevenness detection accuracy Within ± 10 μm
Slit length 12 mm
Slit width 0.5 mm
Line speed *1 1m to 1500m/min
Responsiveness 3Hz to 30kHz
Sampling frequency 150kHz
Power consumption 3.5W or less
Operating envirornment -5 to 50 ° C (without condensation)
Weight 0.8kg

*1 Due to the height of the unevenness, the linear speed range changes.

FM-L / Surface Fault Detector

※Please swipe right.

Type FM-44L FM-66L FM-88L
CAD file dxf dxf dxf
pdf pdf pdf
Detector Number of Detection sensors 4 (all circumferential inspection) 6 (all circumferential inspection) 8 (all circumferential inspection)
The outer diameter to be measured φ 1 to 30 mm φ 10 to 60 mm φ 20 to 130 mm
Line speed 1 to 400 m / min 1 to 400 m / min 0.2 to 300 m / min
Detection capability Detects defects of φ1 mm × 1 mm (height of concavities and convexities) (detection capability depends on the shape and color of the defect part)
Alarm level 0 to + 10V continuous variable 0 to + 10V continuous variable 0 to + 1V continuous variable
Alarm output Red lamp on, "a" contact 0.5 sec per one shot / every detection
Recorder output There is output for analog recorder for each channel.
Power supply AC 100 V 50/60 Hz 50 VA AC 100 V 50/60 Hz 55 VA AC 100 V 50/60 Hz 70 VA
External Dimensions 400 x 36 x 200 [mm] 576 x 576 x 458 [mm] 700 x 710 490 [mm]
Weight 13kg 35kg 45kg
Light source lamp 4 6 8
LED lamp (manufactured by Ushio) LDR 7 L - M - E 11/27/5/18
Power supply No external power supply required
Operating temperature -5 to 50 ° C (without condensation)

ID ・ IDS ・ IDX / Joint Detector

※Please swipe right.

Detection principle Proximity type magnetic power generation type Through type eddy current loss type Penetrating eddy current loss
bridge magnetism
resistance detection type
Penetrating eddy current loss
high sensitivity
bridge magnetism
resistance detection type
Model No. [S] ID-3L ID-5 ID-8 ID-15 ID-30 ID-50 ID-90 IDS-24 IDS-60 IDS-100 IDX-06
[C] ID-1001/1001W IDS-501 IDX-701
Exterior photo photo photo photo photo
Sensor's
CAD file
dxf dxf dxf dxf dxf dxf dxf dxf dxf dxf dxf
pdf pdf pdf pdf pdf pdf pdf pdf pdf pdf pdf
Controller's
CAD file
-- dxf dxf dxf
pdf pdf pdf
[S]
Outline
[mm]
W 30 22 30 38 50 70 110 74 150 201 66
H 30 52 65 80 90 125 175 53.2 113.2 160 47.2
D 22 7 8 10 10 25 38 76 120 124 51
Through hole diameter (mm) (Detection distance 15 mm) φ5 φ8 φ15 φ22.5 φ50 φ90 φ24 φ60 φ100 φ6
[C] Outline (mm) 120 x 100
× 55
150 × 120
× 75
160 × 150
× 90
140 × 137
× 101
Power supply AC 100 V 50/60 Hz AC100 / 200V 50 / 60Hz power supply notification output included
Power consumption 2VA 3VA 5VA 12VA or less
Detect output Red LED on, 0.5 second one shot "a" contact
Signal monitor None Bar graph LED display
Sensitivity setting method
  • 1 turn volume
  • 10 rotary dial
  • 10 rotary dial
  • 5 step sensitivity switching
  • 10 rotary dial
  • Line wobble adjustment dial
Temperature and humidity 0 to 50 ° C, 35 to 85% RH (without condensation)
Features
  • Support within φ10
  • Sensitive to magnetic material (iron)
  • It is not sensitive to copper material
  • Shielded wire available
  • Detection area Attention
  • Sensor types abundant
  • Sensitivity to every metal material
  • Sensitivity to twisting and alloy bonding
  • Not suitable for shielded wire
  • Be careful of line vibration
  • Responsive to metal (magnetic material)
  • Sensitivity to twisting and alloy bonding
  • Also suitable for shielded wire
  • Resistant to vibration of the wire
  • Sensitivity to every metal material
  • Sensitivity to twisting and alloy bonding
  • Also suitable for shielded wire
  • Resistant to vibration of the wire
Exterior photo(ID ・ IDS ・ IDX / Joint Detector)
  • Outer dimension[W * H * D] 120×100×55(mm)
    ID-3L

  • Outer dimension[W * H * D] 150×120×75(mm)
    ID-1001

  • Outer dimension[W * H * D] 160×150×90(mm)
    IDS-501

  • Outer dimension[W * H * D] 140×137×101(mm)
    IDX-701

  • Outer dimension[W * H * D] 74×76×54(mm)
    IDX-06(sensor section)

CDD-15 / Cable Disconnection Detector

※Please swipe right.

Model No. CDD-15
Detector Electrode material SUS304
Maximum passable cable external diameter Φ15
Guaranteed temperature upper limit range 70℃
Operating temperature 1°C to 70°C
Minimum detection cable Effective cross section 0.005mm 2 or more / Finished External diameter Φ0.165 mm or more
Disconnection length of detection 15mm or more
Maximum line speed 2000 m/min
External Dimensions 30 x 50 x 52 [mm] (including connector)
How to connect with the alarm unit Connection using coaxial cable standard 1.5m
Alarm output unit Power supply AC100 or 200V ± 10% 4VA
Alarm output format ・ With red LED lighting ・ Contact output (1 point) 0.5 sec One shot AC250V 2A (resistance load)
Operating temperature 10 to 50°C
External Dimensions 97 x 131 x 50 [mm]

DC series / Conduction checker

DC-1000K

※Please swipe right.

Model No. DC-1000K
CAD file dxf pdf
Outline For multicore cables, inspect the disconnection under normal conduction test, apply high voltage to one side and inspect crosstalk
Discriminating Resistance Break wire 1 kΩ ± 5%
Contact wire 50 kΩ ± 5%, 100 kΩ ± 5%, 200 kΩ ± 5%
Testing voltage Disconnection DC 24V
Entaglement DC 0 to 1000 V
Output Alarm buzzer
Power supply AC 100 V 50/60 Hz 20 VA
External Dimensions 350 x 100 x 331 [mm]
Weight Approximately 4.5 kg
DC-12K

※Please swipe right.

Type DC-12K
CAD file dxf pdf
Judgment resistance 100 Ω to 2000 Ω (can be changed by option)
Applied voltage DC 9 V (AC adapter) or DC 6 V (AA batteries)
Buzzer volume 90 horn / m or more. (When AC adapter is used)
Test lead wire Red / Black 1m each (banana chip ・ alligator clip ・ needle shaped terminal)
Dry battery AA 1.5V 4 pcs
AC adapter Input AC 100V ± 10% 6VA Output DC 9V 0.3A
External Dimensions 158 × 95 × 35 [mm]

DAC series / Outer diameter control unit

※Please swipe right.

Model No. DAC-86B DAC-76A DAC+88
CAD file dxf dxf dxf
pdf pdf pdf
Control Method P / I / SPEED control system Delay time step control method Parameter setting control method
Automatic start-up function × ×
Applicable Micrometers OK if there is analog deviation output Only our company
Signal input section Input type Outer diameter deviation input,
speed voltage input
Outer diameter deviation input Extrusion speed voltage,
take-off speed voltage
Input isolation
Input range OD input: DC ± 10 V
Speed ??ON: DC0 to + 10V
OD input: DC ± 10 V Extrusion input: DC 0 to + 10 V Take-up input: DC 0 to + 10 V
Input impedance 200kΩ 200kΩ 200kΩ
Error gain setting × 10 μm / V to 10 mm / V (10 times step variable) ×
Signal output section Output type Control output Control output Extrusion speed voltage, Take-off speed voltage
Output method Correction control method Correction value control method Absolute value control method
Output isolation
Output range DC ± 10 V DC ± 10 V Each output DC 0 to + 10 V
Maximum current DC ± 20 mA DC ± 20 mA Each output DC 0 to + 10 mA
Output impedance 6 Ω or less 6 Ω or less Each output 10 Ω or less
Limit voltage setting
Setting Items P, I Alarm level, P System data (11 types) [*1] Work data (12 types)
Programming function × × ○ (storing 100 kinds of data)
Driving button Manual / Automatic / Reset Manual / Automatic / Reset Manual / Automatic / Rising / Decelerating
External operation input
Measuring pulse signal No need necessary
Set distance etc. from the back Built-in + 12V power supply for sensor
No need
Main display On the LED bar graph
Control output display
With an analog meter Control output display Display setting value and operation status indication in LCD.
RS-232C ×
Tacho-generator input × ×
Power supply AC 100 to 240 V 50/60 Hz free power supply
Power consumption 8 VA or less 15VA or less 10VA or less
Operating envirornment Temperature: 0 to 45 ° C, Humidity: 30 to 85% (without condensation)
External Dimensions 144 x 72 x 191 [mm] 350 x 99 x 331 [mm] 144 x 72 x 191 [mm]
Weight Approx 1.5 kg Approx 3 kg Approx 1.7 kg

[*1] Once set at installation, it is not necessary to set it for each operation because it is backed up with a battery.  ○: Yes, ×: none

PRF / Profile Extrusion Control System

※Please swipe right.

Edge sensor Detection method Non-contact / infrared optical fiber system
PRF-10H
PRF-40H
Measuring area 1 mm × 20 mm (PRF - 10 H), 4 mm × 20 mm (PRF - 40 H)
Resolution ± 1 μm
Accuracy ± 5 μm
Operating temperature 300 ℃ max
Outline dimension 360 x 45 x 20 [mm]
Weight 400 g
Controller Deviation display Analog meter → ± 0.5 mm (PRF - 10 H), ± 2 mm (PRF - 40 H)
PRF-93 Deviation output Analog voltage → ± 4 V / ± 0.5 mm (PRF - 10 H), ± 4 V / ± 2 mm (PRF - 40 H)
Upper / lower limit output Multistage setting possible, contact output 250 V 1A
Power supply AC 100 to 240 V 50/60 Hz 10 VA
Outline dimension 144 x 72 x 191 [mm]
Weight 1.5kg
Controller unit Use DAC - 86B (refer to the specification of DAC - 86B)
Sensor mounting bracket Prepared separately
CAD file PRF-93 dxf pdf
PRF-10H dxf pdf
PRF-40H dxf pdf

OM - 01 / Reverse Detector

※Please swipe right.

Model No. OM-01
CAD file dxf pdf
Power supply DC + 12 V / 0.5 A (Modifiable by designation)
Settings 3 digit digital switch
Contact output A contact, 500 ms one shot, AC 240 V 1A (resistance load)
Count input A phase / B phase
Maximum count rate 5 kHz (remodelable)
View Power supply LED and reverse running indication LED
Prohibited gate Output disabled at terminal short circuit or "L" level (CMOS level of 5 VDC)
External Dimensions 100 x 70 x 112 [mm], DIN rail mounting is possible.

OM - 02 / A/B Phase Divider

※Please swipe right.

Model No. OM-02
CAD file dxf pdf
Power supply DC + 12 V / 0.5 A (Modifiable by designation)
Division ratio 10-dividing and 100-dividing
Divided output Open collector output
Count input A phase / B phase
Maximum count rate 10 kHz (remodelable)
Single phase / two phase switching Switch by jumper on internal board
External Dimensions 100 x 70 x 112 [mm], DIN rail mounting possible

OM - 03 / 2-Channels Distributor

※Please swipe right.

Model No. OM-03
CAD file dxf pdf
Power supply DC + 12V / 0.5A (Modifiable by designation)
Input 2 lines (built in 4.7 kΩ pull-up resistor)
Output 5 outputs / 1 channel (open collector output)
Maximum count rate 10 kHz (remodelable)
External Dimensions 100 x 70 x 112 [mm], DIN rail mounting is possible.

VI Series / Variable Constant-Current Power Supply

※Please swipe right.

Model VI-101
(Build-to-order manufacturing)
VI-102
(Build-to-order manufacturing)
CAD file dxf pdf dxf pdf
Input command voltage DC0 to + 10V
Output current DC 0 to 1A (variable range: 0.1 to 1A), ripple current: within 0.5% DC 0 to 2A (variable range: 0.2 to 2A), ripple current: within 0.5%
Maximum output voltage DC 0 to + 25 V DC 0 to + 28 V
Input / output isolation voltage ± 2000 Vp
Control Mode CMOS power transistor serial constant-current control
Power supply AC 200 V (100 V AC is also possible by designation) 50/60 Hz 30 VA AC 200 V (100 V AC is also possible by designation) 50/60 Hz 60 VA
Operating temperature -5 to 50 ° C
External Dimensions 130 x 85 x 102 [mm] 180 x 144 x 84 [mm]
Weight 1.0kg 1.5kg

AD Series / Counting Event Printer

※Please swipe right.

Type AD-500
CAD file dxf
pdf
Measure function Display 6 digits green / red 2 color 7-segment LED
Clock Pulse Correspondent to single phase pulse / A phase B phase pulse. Up / Down count enabled
Clock pulse rate Up to 2 kPPS / 100 PPS, selectable
Pulse rate From 0.00001 m / pulse to 999999 m / pulse Arbitrary setting in the range is possible
Power Supply for ditector DC + 12V maximum 70 mA
Event input Number of event messages 10 types
Message event input Rear terminal block
Reset event input Front panel switch, rear terminal block, RS-232C
Print event input Front panel switch, rear terminal block, RS-232C
Change message event name RS-232C / Changeable via USB memory
Various settings Various parameter settings 6 digits green 7 segments Digital setting with LED
PRESET 1 (Full amount) 6 digits (absolute value setting)
PRESET 2 (forecast) 6 digits (absolute value setting, or also setting relative value to PRESET 1 are possible. )
Each PRESET output Scale value 7 segments Red display, Front panel LED, relay contact, RS-232C
Initial set 6 digits
lot number 4 digit, automatic update is possible
Event input distance correction More accurate measurement can be done by setting the correction distance of each message event.
Printing Printer 58 mm width 20 digit thermal printer
No recording paper output Front panel LED, relay contact, RS-232C
USB Memory controller USB 2.0 host controller
Functions Event data save to USB memory, Set value load / save.
Marker output Relay contact output, pulse width can be set in units of 1 ms in the range of 0 msec to 60000 msec
Clock function Year, date, hour, minute
Battery backup Backing up the scale / clock / various settings (Backup time: 1 month or longer)
External communication RS-232C standard equipment (Baud rate 9600/19200 bps)
Power supply AC 90 to 240 V free power supply 50/60 Hz
Power consumption 8 VA or less
Operating temperature 0 to 45 ° C
Operating Humidity 35 to 85% (without condensation)
Shape 144 x 144 x 180 mm (DIN size compliant)
Weight Approx 2.8 kg
[AD.2] Difference between AD-50,AD-50E and AD-500

※Please swipe right.

Functions AD-50 AD-50E AD-500
Number of event messages 10 types 7 types 10 types
Clock pulse rate Selectable from 2kPPS and 10PPS. Up to 2 kpps Selectable from 2kPPS (maximum) and 10PPS.
Reset event message input Switchs on front panel, terminal block on rear panel, RS-232C Front panel switch Switchs on front panel, terminal block on rear panel, RS-232C
Change message event name Can be changed through RS-232C Changeable in data setting mode Can be changed through RS-232C or USB Flash
Alarm output for expiration, forecast (PRESET) setting and other settings Alarm output available No function Alarm output available
Initial set digit number 6-digits 5-digit 6-digits
Lot number digits 4-digits 3-digits 4-digit (can be updated automatically)
External communication RS-232C No function Equip RS-232C as standard (baud rate: 9600/19200bps)

RS-Printer / Printer for Laser Micrometer

※Please swipe right.

Model No. RS-PRINTER
CAD file dxf pdf
Printer 20 characters 58 mm Thermal system
Serial communication condition Connected with Takikawa Engineering Laser OD measuring instrument.LDM-110, 110EX, 210, 1000, 1000EX
Communication speed There are differences depending on model (Initial value: 9600 bps)
Power supply AC 100 to 240 V free power supply 50/60 Hz 15 VA or less
Outline dimension 180 x 90 x 210 [mm]
Ambient temperature and humidity 0 to 45 ° C, 35 to 85% RH (without condensation)

MAC / Defect portion marking device

※Please swipe right.

Spray marker
Model No. MAC-01
Exterior photo Photo
CAD file dxf pdf
Marking material Water-based paint (spray type)
Removal of marking material Difficult
Marking material supply (Recommended) Asahippen water news play 300ml
Passing hole diameter None
Recommended outer diameter of passing material Unlimited
Transit speed Unlimited
Marking delay 1 - 12 seconds (variable)
Marking time 1 - 5 sec (variable)
Repeat interval Sum of marking time and delay
Power Supply AC 100 V 50/60 Hz
Power consumption 30VA
Supply air No need
External Dimensions 62 × 270 × 90 [mm]
Spray marker MAC-01
  • Outside Dimension:[W * H * D]62×270×90(mm)MAC-01

  • A figure with actual spray cans
    Setting of Spray

EMAC / Elastoring Marker (Defective portion marking device)

※Please swipe right.

Elast string marker
Model No. EMAC-005 EMAC-009 EMAC-019 EMAC-041 EMAC-057 EMAC-160 EMAC-245
(Please inquire)
Exterior
photo
Photo Photo Photo Photo Photo Photo Photo
CAD file dxf dxf dxf dxf dxf dxf dxf
CAD file pdf pdf pdf pdf pdf pdf pdf
Marking
material
Elastic rubber cord material
Removal
of marking
material
Easy
Marking
material
supply
Supply bobbin winding rubber cord from our company
Passing
hole
diameter
5mm 9mm 19mm 41mm 57mm 160mm 245mm
Recommended
outer
diameter
of passing
material
0.5 - 3mm 1 - 6mm 3 - 10mm 10 - 35mm 20 - 40mm 50 - 120mm 100 - 200mm
Passing
through
speed
Unlimited
Marking
delay
(Up to 0.2 sec (fixed)
Marking
time
A moment
Repeat
interval
3.5 seconds or less 6 seconds or less
Power Supply AC 100 - 240 V 50/60 Hz
Power consumption 50VA
Supply air 4 kg / cm 2
Dimensions [mm] 360 x 190 x 590 (Excluding rubber supply section) Weight: Approx. 12 kg 3360 x 380 x 190 (Excluding rubber supply section) Weight: Approx. 20 kg 350 × 248 × 440 (Excluding rubber supply section) Weight: Approx. 45 kg 550 × 248 × 717 (Excluding rubber supply section) Weight: Approx. 45 kg
Elastoring marker EMAC-160/245
  • EMAC-160

  • EMAC-245

Elastoring marker EMAC-005/009
  • EMAC-005

  • EMAC-009

Elastoring marker EMAC-019
  • EMAC-019

Elastoring marker EMAC-041/057
  • EMAC-041

  • EMAC-057

AL-03 / Alarm unit

※Please swipe right.

Model No. AL-03
CAD file dxf pdf
input No-voltage contact signal (closing time: 0.1 seconds or more)
output Lighting with parol car light, buzzer warning, counter memory
Reset Alarm will stop with front reset switch
External Dimensions 110 x 315 x 85 [mm]
Power supply AC 100V 50/60 Hz 15VA

DSP / External display unit

※Please swipe right.

Model No. DSP-4B DSP-48
CAD file dxf pdf dxf pdf
Power supply AC 100 V 50/60 Hz (DC 24 V 80 mA) AC 100 to 240 V 50/60 Hz
Input BCD negative logic, open collector input
Output Maximum 100 m
Maximum count rate Red 7-segment LED character height 15 mm / 4 digits Orange 7 segment LED character height 76.2 mm / 4 digits
External Dimensions 72 x 36 x 119 [mm] 310 x 140 x 140 [mm]

Caution) About DSP-4B
There is no compatibility between DSP-4 and BCD cable.
In DSP-4, AC 100 V power supply was built in, but DSP-4B becomes separate body.

RS-485 system

※Please swipe right.

Interface EIA RS-485 compliant (electrical performance)
Communication method Half duplex communication
Synchronization method Asynchronous type
Maximum Total Extended Distance 1200 m
Connection type 1: N multi-drop connection (optional 7 measuring instruments)
Transmission mode MODBUS_RTU Binary method
Communication speed Selectable by parameter setting ~ 57600 bps
Bit length 8 bits
Start / Stop bit 1 bit
Parity bit None
Error check code CRC-16 scheme cyclic code
Compatible models LDM series (Laser Micrometer) LDM-1000 / 1000EX excluded
CPM-401 (capacitance monitor)
EM series (eccentricity monitor)
TM series (surface variation detector)
IDX-702 (joint detector)
Spark tester (manufactured by Clinton)
EMAC series (elastring marker)

Precautions on Using Printer Equipment

* The mechanical part of the printer is consumable.
Please note that it may be repaired for a repair charge even within the warranty period.

* Usage notes
・ Don't print when printing paper is not set.
・ When sending paper, be sure to use the FEED switch.Pulling the paper without using the FEED switch may cause malfunction.
・ Please do not drop or hit the printer.Do not disassemble or repair by yourself.
・ Do not wet the printer with water.Please do not use it by removing the panel.
・ Please do not pull the printing paper from the insertion slot in the reverse direction as it will cause malfunction.
・ If there is a problem with the printer (unusual noise, smell, smoke etc.) turn off the power immediately, please contact us after checking that abnormality is not continuing.

*Precautions for handling thermal paper
Thermal paper is a special paper that's surface is specially treated with chemicals and is designed to develop color by thermochemical reaction.
Please pay attention to the following points.
・ Please save it in a dry cool dark place.
・ Do not scrape strongly with a hard object, or do not place it near organic solvents.
・ Please do not touch the PVC, eraser or adhesive tape for a long time.
・ Do not overlap diazo or wet copy just after copying.
・ Please do not use artficial paste when gluing.
・ Adhesive tapes may discolor the thermal paper.
・ Please fix the back side with double sided tape etc.
・ If you touch with sweaty hands, fingerprints may be attached or printing may be blurred.
・ Please use designated thermal paper.

*Installation
Please use the printer between horizontal or vertical installation.
Do not install or store it in the following places as it will cause malfunction.
・ Dust, dusty places and strong vibration places.
・ Where electromagnetic noise or corrosive gas is generated.
・ Places exposed to direct sunlight, places with high moisture or oil.
・ Places where the temperature is 40 ° C or higher or where the temperature is 0 ° C or lower.
・ Places where the relative humidity is 80 % or more.
・ Considerable places where there is a sudden temperature change and condensation .

Contacts

「Contact」 or 「Technical consultation」etc. are accepted from here.

TEL.+81 42-645-8920

office hour/9:00〜17:30(Weekday)